Revision as of 17:09, 16 August 2024

install hostapd

install latest version:

yay -s hostapd-git

configuration for wifi6e on 6ghz:

###################################################################
# HostAPd configuration for WiFi-6e for a MEDIATEK mt7925 NIC     #
#                                                                 #
# Requirements for WiFi-6e (ieee80211ax) on 6GHz:                 #
# - WPA3 for authentication                                       #
# - SAE key management required for WPA3                          #
# - Management Frame Protection required for WPA3                 #
# - Radar awareness required for some RegDomains on 5GHz and 6GHz #
# - WME/WMM required                                              #
###################################################################
# 
# Posix Socket - (i.e. for hostapd_cli)
ctrl_interface=/var/run/hostapd
# driver interface
driver=nl80211
# NIC to be configured
interface=wlan0
#device_name=wlan0
# This WiFi NIC is a bridge slave...
#bridge=br0
wds_sta=1
# Logging
logger_stdout=-1
logger_stdout_level=0
logger_syslog=-1
logger_syslog_level=0
# Registry Domain configured by Country Code
country_code=DE
ieee80211d=1
# Fulfill requirements for AP operation on 6GHz -- This is an INDOOR ONLY AP
he_6ghz_reg_pwr_type=0
# Expect this AP not to change its position and antenna alignment
stationary_ap=1
he_6ghz_rx_ant_pat=1
# Activate beamforming capabilities 
he_mu_beamformer=1
he_su_beamformee=1
he_su_beamformer=1
# Limit number of concurrent "clients" (stations) and do not restrict them by MAC address
max_num_sta=16
macaddr_acl=0
# Frequency band and channel selection for 6GHz WiFi-6e using 160MHz bandwidth
hw_mode=a
op_class=134
channel=1
he_oper_centr_freq_seg0_idx=15
# Configure for WiFi-6e protocol (AX mode) and set a BSS color
ieee80211ax=1
he_bss_color=1
# Enable Radar detection and DFS support if available
ieee80211h=1
enable_background_radar=1
# Enforce Management Frame Protection (MFP) as required for WPA3
ieee80211w=2
beacon_prot=1
# Configure Ciphers, Re-Keying Intervals and Authentication Protocols for WPA3
wpa=2
wpa_key_mgmt=SAE
auth_algs=1
rsn_pairwise=CCMP CCMP-256 GCMP GCMP-256
group_mgmt_cipher=AES-128-CMAC
extended_key_id=1
wpa_gmk_rekey=86400
wpa_group_rekey=86400
wpa_group_update_count=4
# Configure SSID and Passphrase
ssid=LinuxAP
sae_password=testtest
# 
# Wireless Multimedia Extensions (WME) and Wi-Fi Multimedia (WMM)
wme_enabled=1
wmm_enabled=1
#
# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e):
# These parameters are used by the access point when transmitting frames to the clients.
# Low priority / AC_BK = background
tx_queue_data3_aifs=7
tx_queue_data3_cwmin=15
tx_queue_data3_cwmax=1023
tx_queue_data3_burst=0
# Normal priority / AC_BE = best effort
tx_queue_data2_aifs=3
tx_queue_data2_cwmin=15
tx_queue_data2_cwmax=63
tx_queue_data2_burst=0
# High priority / AC_VI = video
tx_queue_data1_aifs=1
tx_queue_data1_cwmin=7
tx_queue_data1_cwmax=15
tx_queue_data1_burst=3.0
# Highest priority / AC_VO = voice
tx_queue_data0_aifs=1
tx_queue_data0_cwmin=3
tx_queue_data0_cwmax=7
tx_queue_data0_burst=1.5
# Quality of Service (QoS) parameters
# Low priority / AC_BK = background
wmm_ac_bk_cwmin=4
wmm_ac_bk_cwmax=10
wmm_ac_bk_aifs=7
wmm_ac_bk_txop_limit=0
wmm_ac_bk_acm=0
# Normal priority / AC_BE = best effort
wmm_ac_be_aifs=3
wmm_ac_be_cwmin=4
wmm_ac_be_cwmax=10
wmm_ac_be_txop_limit=0
wmm_ac_be_acm=0
# High priority / AC_VI = video
wmm_ac_vi_aifs=2
wmm_ac_vi_cwmin=3
wmm_ac_vi_cwmax=4
wmm_ac_vi_txop_limit=94
wmm_ac_vi_acm=0
# Highest priority / AC_VO = voice
wmm_ac_vo_aifs=2
wmm_ac_vo_cwmin=2
wmm_ac_vo_cwmax=3
wmm_ac_vo_txop_limit=47
wmm_ac_vo_acm=0

Howto hostapd: Difference between revisions

Revision as of 17:09, 16 August 2024

install hostapd

references

Navigation menu